Download Mitsubishi Colt Lancer 2001 Repair Service Manual –

Replacing the coil springs on a Mitsubishi Colt Lancer can be a challenging task, but with careful steps and the right tools, it can be done. click here for more details on the download manual…..

Here’s a simplified guide to help you through the process. Remember, safety is crucial, so make sure to wear protective gear and work in a safe environment.

### Tools and Materials Needed:
1. **Jack and Jack Stands**: To lift and secure the vehicle.
2. **Wrench Set**: To remove bolts.
3. **Spring Compressor**: A tool that safely compresses the coil springs.
4. **Pry Bar**: To help remove and install components.
5. **Safety Glasses**: To protect your eyes.
6. **Gloves**: For hand protection.
7. **New Coil Springs**: Make sure they are the correct size for your vehicle.

### Step-by-Step Guide:

#### 1. **Preparation**
– **Park on a Level Surface**: Ensure the vehicle is on a flat and stable surface.
– **Engage the Parking Brake**: This prevents the vehicle from rolling.

#### 2. **Lift the Vehicle**
– **Loosen the Wheel Bolts**: Slightly loosen the bolts on the wheel where you’ll be replacing the coil spring.
– **Jack Up the Vehicle**: Use a floor jack to lift the vehicle and place jack stands under the vehicle for safety.
– **Remove the Wheel**: Take off the wheel to access the suspension components.

#### 3. **Remove the Old Coil Spring**
– **Locate the Coil Spring**: Identify where the coil spring is located in the suspension system.
– **Remove the shock Absorber**: You may need to remove or disconnect the shock absorber to access the coil spring. Use the wrench to take off the bolts.
– **Compress the Spring**: Attach the spring compressor to the coil spring. Make sure it’s evenly placed on both sides. Gradually tighten the compressor to compress the spring, which will relieve the tension.
– **Remove the Spring**: Once compressed, carefully remove any retaining clips or bolts holding the spring in place, and then gently remove the coil spring from the assembly.

#### 4. **Install the New Coil Spring**
– **Position the New Spring**: Place the new coil spring in the same location as the old one. Make sure it sits properly in its seat.
– **Reinstall the shock Absorber**: If you removed it, put the shock absorber back in place and tighten the bolts securely.
– **Release the Spring Compressor**: Slowly and evenly release the tension on the spring compressor. Once released, double-check to ensure everything is seated correctly.

#### 5. **Reassemble and Lower the Vehicle**
– **Reattach the Wheel**: Put the wheel back on and hand-tighten the bolts.
– **Lower the Vehicle**: Carefully jack the vehicle down and remove the jack stands.
– **Tighten the Wheel Bolts**: Once the vehicle is on the ground, use the wrench to securely tighten the wheel bolts in a crisscross pattern for even pressure.

#### 6. **Final Checks**
– **Inspect Your Work**: Double-check to ensure everything is properly installed download Mitsubishi Colt Lancer workshop manual and secured.
– **Test Drive**: Take the vehicle for a short drive to ensure the new coil springs are functioning correctly and there are no unusual noises.

### safety Notes:
– If at any point you feel unsure about the task, it’s best to consult a professional mechanic.
– Always ensure that the spring compressor is used correctly to avoid accidents, as compressed springs can be dangerous.

By following these steps carefully, you can successfully replace the coil springs on a Mitsubishi Colt Lancer. Good luck!
An airbag is a crucial safety feature in modern vehicles designed to protect occupants in the event of a collision. It is a flexible bag that inflates rapidly during a crash, creating a cushion that absorbs the impact force and reduces the risk of injury to passengers. Airbags are typically housed within the steering wheel, dashboard, side panels, and even the roof of the vehicle, depending on the type of airbag system installed.

The operation of an airbag system is triggered by sensors that detect deceleration or impact. These sensors are usually located throughout the vehicle, monitoring the forces exerted during a crash. When a collision occurs, the sensors send a signal to the airbag control unit, which initiates the inflation process. This is achieved by igniting a chemical propellant that rapidly produces gas, inflating the airbag in a fraction of a second—often within 20 to 30 milliseconds.

Airbags come in various types, including frontal airbags, side-impact airbags, curtain airbags, and knee airbags, each serving a specific purpose in enhancing passenger safety. Frontal airbags deploy in head-on collisions, while side-impact airbags protect against lateral impacts. Curtain airbags deploy from the roofline to protect occupants’ heads during rollovers or side collisions.

Though airbags significantly reduce the severity of injuries during crashes, they are most effective when used in conjunction with seat belts. Proper usage of both safety devices is essential, as airbags are designed to work as a complementary system rather than a standalone safety measure. Overall, airbags have become a standard feature in vehicles, contributing to the ongoing effort to improve Automotive safety and protect drivers and passengers alike.