Adjusting the parking brake on a Dodge Neon SRT-4 can be a straightforward task, especially if you follow these simple steps. click here for more details on the download manual…..
- Ed Peters Tech Talk on the Neon/Neon SRT4 and Caliber SRT4 Transmission Mr Ed Peters, a retired Chrysler engineer and Neon racer, gives a tech seminar on the T350 and T850 transmissions in the 95-05 …
- SRT-4 problems – Misfire & Code Check You can clearly feel, hear and see a misfire while under a slight load. Also did a code check after… Not sure what could cause the …
Here’s a guide that breaks down the process in an easy-to-understand manner:
### Tools You May Need:
– **Socket set** (usually 10mm and 13mm sockets)
– **Wrench**
– **Pliers**
– **Jack and jack stands** (if necessary)
– **Lug wrench** (if you need to remove wheels)
### Steps to Adjust the Parking Brake:
1. **Safety First**:
– Make sure the car is on a level surface.
– Engage the parking brake to keep the car from rolling.
– If you need to lift the car, use a jack and secure it with jack stands.
2. **Check the Brake Levers**:
– Inside the car, pull the parking brake lever up. Count how many clicks it takes for the lever to fully engage. Ideally, it should take about 3 to 5 clicks. If it takes more than that, it may need adjusting.
3. **Locate the Adjustment Mechanism**:
– The parking brake adjustment is typically done at the rear brakes. In the case of the Dodge Neon SRT-4, you may need to remove the rear wheels to access the brake assembly.
– Use the lug wrench to loosen and remove the lug nuts, then take off the rear wheels.
4. **Inspect the Brake Components**:
– Look for the brake caliper (the part that squeezes the brake pads against the brake rotor).
– Check the parking brake cable that runs from the lever inside the car to the rear brakes.
5. **Adjust the Parking Brake**:
– Find the adjustment nut or screw on the parking brake cable. This is usually located near the caliper or at the end of the cable.
– Using a wrench or pliers, turn the adjustment nut clockwise to tighten the cable. This will increase the tension and should help reduce the number of clicks needed to engage the parking brake.
– **Tip**: Adjust it in small increments and check the lever again to see if it feels right.
6. **Reassemble Everything**:
– Once you’re satisfied with the adjustment, put the wheel back on and hand-tighten the lug nuts. Lower the car back to the ground if you’ve lifted it.
– Tighten the lug nuts in a crisscross pattern to ensure they are secure.
7. **Test the Parking Brake**:
– With the car on a flat surface, pull the parking brake lever again to see how many clicks it takes to engage. It should feel firm
and hold the car in place.
– If it still feels loose or requires more adjustment, you may need to repeat the adjustment process.
8. **Final Check**:
– After adjustments, take the car for a short drive and test the parking brake again to ensure it works properly.
### Important Note:
If at any point you feel uncomfortable or unsure about the process, it’s best to consult a professional mechanic. Safety is the top priority when working on your vehicle!
By following these steps, you should be able to adjust the parking brake on your Dodge Neon SRT-4 successfully. Good luck!
The dimmer switch is an essential component in a vehicle’s electrical system, primarily responsible for controlling the brightness of the dashboard lights and other interior lighting. This switch allows drivers to adjust the illumination levels according to their preferences and driving conditions, enhancing visibility and comfort while minimizing distractions.
Typically located on the dashboard or integrated into the headlight control mechanism, the dimmer switch operates through a simple mechanism that either increases or decreases the voltage supplied to the lights. By turning the switch or sliding a dial, drivers can find the optimal brightness that suits their needs, particularly during nighttime driving or in low-light conditions. This functionality is crucial as overly bright lights can be distracting and may hinder a driver’s night vision, while insufficient light can make it difficult to read essential information on the dashboard.
Modern vehicles often feature electronic dimmer switches that incorporate advanced technology, allowing for more precise control and integration with other vehicle systems. Some systems automatically adjust brightness based on ambient light, ensuring optimal visibility at all times. Additionally, the dimmer switch may also control the illumination of other interior components, such as buttons and knobs, contributing to a cohesive and aesthetically pleasing driving environment.
Overall, the dimmer switch plays a vital role in enhancing the driving experience by providing comfort, safety, and convenience through adjustable lighting.